Fluke - ii900 Sonic Industrial Imager

Product Overview:

  • Do more with the same air compressors–delay the capital expense of installing an additional compressor
  • Ensure proper air pressure to your pneumatic equipment
  • Lower energy costs
  • Reduce leak detection time
  • Improve reliability in your production line
  • Make leak detection part of your typical maintenance routine
  • Train the team in a matter of minutes
  • Validate repairs on the spot

More

Leaks in compressed air, gas and vacuum systems hit both production uptime and the operations bottom line.

While this is a known issue, locating air leaks has been a time-consuming and tedious–until now. With the Fluke ii900 Sonic Industrial Imager your maintenance team can quickly pinpoint the location of compressed air and vacuum leaks. With minimal training, your maintenance technicians can begin checking for air leaks during their typical maintenance routine–even during peak operation hours.

This industrial imager offers a new way to locate issues using sound. It is an intuitive, simple to use tool that can isolate the frequency of leaks or vacuums, even in extremely noisy production environments. A leak location is determined by discerning the direction from which a sound originates by the time delays that occur as the sound passes over an array of microphones. A SoundMap™ is displayed in color over a visual image allowing for easy visual location. With the full array of microphones, it is easy to scan a large area and even capture leaks from a distance.

Finally a better way, quick, simple compressed air, gas and vacuum leak identification.

Fluke ii900 Sonic Industrial Imager

Includes:

  • Imager
  • AC power supply and battery pack charger (including universal AC adapters)
  • Two rugged lithium ion smart battery packs
  • USB cable
  • Rugged, hard carrying case
  • Adjustable hand strap and neck strap
Sensors
# of microphones 64 digital MEMS microphones
Frequency band 2 kHz to 52 kHz
Sound pressure sensitivity Detects a 0.005 CFM leak at 100PSI from up to 32.8 feet
(Detects a 2.5 cm3/sec leak at 7 bar from up to 10 meters)
Operation distance range 0.5 to > 50 meters (1.6 to > 164 feet)*
Field of View 63 ° ± 5 °
Minimum Frame Rate 12.5 FPS
*Depending on ambient conditions
Built-in digital camera (visible light)
Field of View (FOV) 63 ° ± 5 °
Focus Fixed lens
Display 7" LCD with backlight, under-sunlight readable
Resolution 1280 x 800 (1,024,000 pixels)
Touchscreen Capacitive
Acoustic Image Yes, SoundMap™ image
Image storage
Storage capacity Internal memory with the capacity for 999 picture files or 20 video files
Image format Blended visual and SoundMap™.JPG or .PNG
Video format Blended visual and SoundMap™.MP4
Video length 30 seconds
Digital export USB-C for data transfer
Acoustic Measurements
Measurement range 29.3 dB to 119.6 dB SPL (±2 dB) at 2 kHz
21.9 dB to 112.3 db SPL (±2 dB) at 19 kHz
36.6 db to 126.9 dB SPL (±2 dB) at 52 kHz
Auto max/min dB gain Auto or manual, user selectable
Frequency band selection User selectable through user-made presets or manual entry
Software
Ease of use Intuitive user interface
Trend graphs Frequency and dB scale
Spot markers dB level reading at center point of the image
Battery
Batteries (field-replaceable, rechargeable) Rechargeable Li-ion, Fluke BP291
Battery life 6 hours (product includes spare battery)
Battery charging time 3 hours
Battery charging system External dual-bay charger, EDBC 290
General Specifications
Standard palettes 3: Grayscale, Ironbow, Blue-Red
Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature -20 °C to 70 °C (-4 °F to 158 °F) Without batteries
Relative humidity 10 % to 95 % non-condensing
Size (H x W x L) 186 mm x 322 mm x 68 mm (7.3 inches x 12.7 inches x 2.7 inches)
Weight (battery included) 1.7 kg (3.75 pounds)
Main unit rating IP40 protection against particles 1mm or greater and dripping water
Sensor head rating IP51
Warranty 2 year
Self-diagnostic notification Array-health test to identify when microphone array needs attention
Supported languages Dutch, English, Finish, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Simplified Chinese, Spanish, Swedish, Traditional Chinese
RoHS compliant Yes
Safety
General Safety IEC 61010-1
Electromagnetic Compatibility (EMC) International IEC 61326-1: Portable Electromagnetic Environment IEC 61326-2-2
CISPR 11: Group 1, Class A
Korea (KCC) Class A Equipment (Industrial Broadcasting & Communication)
USA (FCC) 47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.

More Product Information

  • Identify complex signal problems fast
  • Supports accurate measurements on VFDs using a low-pass filter
  • Captures intermittents as fast as 250 µS with Peak Capture

  • Optional magnetic hanger for easy set-up and viewing while freeing your hands for other tasks
  • Large digit display with bright, two-level backlight makes the 83V significantly easier to read than older models
  • 6000 counts, 3-3/4 digits
  • Measure up to 1000 V AC and DC
  • Measure up to 10 A, 20 A for up to 30 seconds
  • Frequency to 200 kHz and % duty cycle
  • Resistance, continuity and diode test
  • 10,000 µF capacitance range for components and motor caps
  • Min/Max-Average recording with Min/Max Alert to capture variations automatically
  • Relative mode to remove test lead interference from low ohms measurements
  • Auto and manual ranging for maximum flexibility
  • Touch Hold to capture stable readings avoiding noisy signals
  • Large display digits and two-level bright white backlight for increased visibility
  • Analog bargraph for fast changing or unstable signals
  • Input Alert provides audible warning against wrong use of input jacks
  • Improved selectable sleep mode for long battery life
  • Access door for fast battery changes without breaking the calibration seal
  • "Classic" design with new removable holster with built in test lead and probe storage
  • Lifetime warranty
Electrical safety
All inputs are updated to the 3rd edition of ANSI/ISA S82.01 and EN61010-1 CAT IV 600 V and CAT III, 1000 V. They can withstand impulses in excess of 8.000 V and reduce risks related to surges and spikes.
  • Measure AC current with an optional current clamp accessory

  • True-RMS accuracy with manual and automatic ranging, Display Hold, Auto Hold, and Min/Max-Average recording give you the results you need.
  • Fluke-i400 AC 400A Current Clamp turns the 289 into a clamp meter.
  • Safety rated CAT III 1000 V, CAT IV 600 V meter to get you home safely from the job.

  • Dual-input digital oscilloscope and multimeter in a ScopeMeter® test tool
  • Available with a 40 MHz or 20 MHz oscilloscope bandwidth
  • Features Connect-and-View™ trigger simplicity for hands-off operation
  • Includes IntellaSet™ technology to automatically and intelligently adjust numerical readout based on measured signal
  • Provides a dual-input waveform and meter reading recorder for trending data over extended periods

  • Precise laser technology for more accurate and repeatable measurements
    • Temperature accuracy of up to ± 1℃ or ± 1% of reading whichever is greater with 20:1 distance to spot ratio
  • Flashlight and large, easy-to-read backlit LCD display for easy viewing even in dark environment
  • IP54 rated for extra protection against airborne contaminants
  • Get your tool to work when you can't - set time and desired interval between measurements and Auto Capture will capture spot temperatures unattended
  • 99 data point logging
  • 30 hour battery life so your tool can perform as long as you need it to
  • Displays the minimum, maximum or average temperature, or the difference between two measurements
  • Hi and Lo alarms for rapid display of measurements outside set limits
  • Small and lightweight design fits easily into your tool box
  • Powered by one (1) AA alkaline battery

  • Large display
  • Backlight for work in dim areas
  • Min / Max to record signal fluctuations
  • Ergonomic overmolded housing with integrated probe holders
  • Free your hands with the optional TPAK magnetic hanger
  • Auto and Manual ranging
  • Meets Measurement Category 1000 V CAT III and Category IV 600 V safety standards
The 77 IV replaces the 77. Move up to superior utility and safety today.

  • VCHEK™ LoZ low impedance measurement function to simultaneously test for voltage or continuity*
  • True RMS for accurate AC measurements on non-linear loads
  • A large backlit display allows for easy visibility in low-lit areas
  • Record signal fluctuations using the Min/Max function
  • Diode test for testing general-purpose germanium, silicon, and power diodes
  • Integral holster with probe holders for easy storage
  • Auto and Manual ranging for added user functionality
  • The optional TPAK magnetic hanger allows the user hands-free flexibility

  • Ideal Digital Multimeter for “go/no-go” testing
  • Features AutoVolt automatic AC/DC voltage selection
  • Includes low input impedance to help prevent false readings due to ghost voltage
  • Presents a large white LED backlight for working in poorly lit areas
  • Measures resistance, continuity, frequency, and capacitance
  • Provides Min/Max/Average with elapsed time to record signal fluctuations

  • Detects and pinpoints the exact location of the SF6 leak – without shutting down equipment
  • Quick entry/exit button allowing quick toggling between gas imaging and infrared mode
  • 320 x 240 resolution for gas and infrared images; SuperResolution increases to 640 x 480, only in infrared mode
  • Get in-focus images in both infrared and gas modes with a touch of a button with LaserSharp® Auto Focus
  • Wirelessly connect your camera to the Fluke Connect® system to make faster decisions. Team members can see the same data and collaborate on identifying the problem or authorize work before you've left the inspection site.
  • No need for pencil and notebook:
    • IR PhotoNotes™ annotation system captures digital images of equipment details, e.g. serial numbers and surrounding area conditions
    • Record any additional notes with voice annotation and save them with the image
  • See additional details with optional smart lenses – no calibration required when swapping them between compatible cameras
  • Optimize images, perform analytics, generate quick, customizable reports and export images to the format of your choice with SmartView® desktop software, included with your purchase
  • Capture clear, accurate infrared images focused throughout the entire field of view with MultiSharp™ Focus
  • Small and lightweight, fits easily into your tool box

Fluke Corporation

Since its founding in 1948, Fluke has helped define and grow a unique technology market, providing testing and troubleshooting capabilities that have grown to mission critical status in manufacturing and service industries. Every new manufacturing plant, office, hospital, or facility built today represents another potential customer for Fluke products.

From industrial electronic installation, maintenance and service, to precision measurement and quality control, Fluke tools help keep business and industry around the globe up and running. Typical customers and users include technicians, engineers, metrologists, medical-device manufacturers, and computer network professionals — people who stake their reputations on their tools, and use tools to help extend their personal power and abilities.

Fluke has achieved the number one or number two position in every market in which it competes. The Fluke brand has a reputation for portability, ruggedness, safety, ease of use and rigid standards of quality.

Contact Details

Fluke Corporation Headquarters

6920 Seaway Blvd., Everett, WA 98203

Mailing address: PO Box 9090, Everett, Washington 98206-9090

Phone: 1-425-347-6100

Technical Support Email: fluke-info@fluke.com


Thermal Imaging
IR Windows Thermal cameras